PLUMBING BASICS INSTALLING A BATHTUB

Installing a bathtub isn't exactly rocket science, but it does require resolute plumbing, carpentry, besides sometimes, tiling skills. Replacing an old bathtub smuggle a new one is also a moderately difficult project. If its old tub is readily accessible, the sustain can move quickly; if you have to lead a wall to remove the old tub and position the afresh bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make sure we have qualified yourself for the job and are comfortable attempting existent. rather than hiring a contractor to transact over the halfway-completed project, it is better to consider employing one before you begin. Chances are we may need a professional plumber to make tube connections.

This article will aid you install a new bathtub in your bathroom if you have under consideration bought the new tub and don't libido to change the arrangement of your previous water supply pipes.

Your instruments and material checklist should comprise the following:

New Bathtub

Hammer

Pipe Wrenches

Prybar

Safety Glasses

Level

Pliers

Adjustable Wrench

Putty Knife

Screwdriver

Cold Chisel

Tape Measure

Pipe Caps

Preparing for the Installation

Firstly, the supporting frame supplied with the bath should be fitted (if required) according to its manufacturer's instructions.



Next, fit the taps or mixer to the bathtub. When advantageous the tap block, it is important to make categorical that if its tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, intrinsic is also wise to fit a sanctioning plate under the taps unit to prohibit millstone on the bathtub.



Fit the flexible tap connectors to the bottom of the two taps running 2 nuts and olives (sometimes supplied with the tub).



Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through its hole in the bath. Use the point supplied by the manufacturer to fit the plug-hole. canvass the plug-hole outlet for an inlet on its side for the overflow pipe.

Next, fit the end of the flexible overflow pipe to the overflow egress. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.



Connect the trap to the bottom of the waste outlet on its bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.

The bath should whereas sell for hypersonic to be fitted hold its final position.

Removing Old Taps

If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is undo the water supply. After contact so, turn on the taps to drain any water superfluous in the system. the force of removing the existent taps can be quite problematic due to the prohibitive access that is often the case.

Use a basin wrench (crowsfoot spanner) or the tap tool to undo the nut which connects its supply pipes to the taps. count on a cloth ready for its remaining water that will come from its pipes. Once the supply pipes have been removed, use the same tool to loosen the nut that holds its taps onto the bath/basin. You will need to stop the single taps from branch during this activity. Once the taps accept been removed, the holes in the bath/basin will have to be spotless of any old sealing convoluted.

Before moving upon to fit the new taps, compare the back connections on the old taps to the new taps. If the old taps are longer than the new taps, then a sword adapter is required for its new taps to correct.

Installing the Bathtub

Using the two wooden boards under its feet, plant the bathtub in its required position. the wooden boards are helpful in evenly spreading the weight of the bathtub because of the area of its boards instead of focusing integral the weight onto four small points.



the next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads level.



To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; then do the akin for the other resolve.



Switch on the water supply besides check all joints and new pipework for leaks and tighten them if necessary. fill the bathtub and also check the overflow outlet and the normal outlet for leaks.



Finally, fix its bath paneling as described weight the manufacturer's instruction guidebook.



Tiling and sealing around the bathtub should wait until its bathtub has been used at least once through this bequeath settle it into its final position.

Fitting New Taps

If the tails of the new taps are plastic, then you will relish a plastic connector to prevent repairs to the thread. One end of the connector fits on the plastic tail of the tap again the other end provides a connection to the existent supply pipes.

If you need to fit a monobloc, then we consign require reducing couplers, which connects the 10mm pipe of the monobloc to the unvaried 15mm supply pipe.

Next, position its tap in the mounting hole effect the bath/basin ensuring that the washers are in place between the drive and the sink. Secure the tap in implant with its manufacturer provided backnut. heretofore its persuade is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper hot or with normal tap connectors. The former type should be connected to the tap ends first, tightening only by hand. The supply pipes can coming be connected to the other end. Tighten both ends with the spanner after both ends have been connected.

Tiling Around the Bathtub

In the expanse stage the bath meets the tile, it is chief to seal the joins stash a silicone rubber caulking. This is important as its fitting culpability move enough to crack the rigid seal, causing the water to penetrate the wall between the bath and the tiling, leading to complications with dampness and possible leaks to the ceiling below.

You can choose from a variety of coloured sealants to blend in your fixtures besides fittings. They are sold in tubes and cartridges, and are capable of sealing gaps progression to a width of 3mm (1/8 inch). If you have a sophisticated gap to fill, you can fill it with twists of soaked paper or soft rope. Remember to always gorge the bathtub with water before sealing, to allow over the rush experienced when the barrel is prestige use. its sealant can crack fairly early if you do not take into account this movement before sealing.

Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower moat. Plastic strips of coving, which are easy to use and cut to size, are also easily available on its market. It is advisable to fit the tiles using water-resistant or waterproof adhesive and grout.Visit Source
THE BEST INTERIOR ARCHITEC